
High-Rise Blackout Heat: The Thermos Effect
A modern glazed tower is a sealed building that has delegated its habitability to machinery, introducing critical management challenges during a sealed building power outage (power cut). Air temperature, air movement, fresh air supply, and water delivery are all mechanically mediated, and all of them depend on the same electrical supply. The envelope itself is deliberately sealed — that is what makes the energy performance work — which means that when the power stops, the building has no passive mode to fall back on.
The thermos metaphor is apt, but it needs one correction that changes the entire response. A thermos does not fail in both directions. It holds whatever state it is given, and the evidence on how these buildings behave without power points firmly in one direction: the fast, dangerous failure mode of a sealed, heavily glazed tower is heat, not cold.
This matters because the two scenarios call for opposite actions, and the instinct that serves one will worsen the other.
The architectural trap: indoor temperature data for modern apartments (flats)
Evaluating passive survivability metrics for apartments reveals how quickly glazed structures breach safe thermal limits. Lawrence Berkeley National Laboratory modeled a 2018-built facility through a six-day heat wave and a three-day cold snap with no power. The asymmetry in the results is the whole story (Sheng et al., 2023):
Airtightness: Safe hours extended from ~9 to ~16 in cold; heat exposure increased ~20% in heat.
Insulation: Helped in both cold and heat events.
Cool roof/wall coatings: Slightly worse in cold; reduced overheating in heat.
Window film: Shortened safe time in cold; reduced heat exposure ~27% in heat.
Natural ventilation: Reduced heat exposure ~62% in heat.
The decisive comparison is between the new building and an older one built to 1999 standards. The older, leakier, less insulated building was dramatically worse in cold — safe hours fell from 27.4% of the period to 6.8%. But in the heat wave it performed better, and the proportion of residents who would require evacuation dropped from 53% to 3%, precisely because its envelope let accumulated heat escape.
The rates differ as sharply as the direction. In the heat event, the worst-case bedroom crossed the 30 °C (86 °F) standard effective temperature threshold in about 12 hours, with the median at about 20. In the cold event, temperatures fell gradually: the median bedroom took about 27 hours to fall below the vulnerable-population threshold of 17.8 °C (64 °F), and around 60 hours to reach 15.6 °C (60 °F).
Urban Green Council's modeling of New York residential stock reached compatible conclusions: in a summer blackout, a typical all-glass building climbs to almost 90 °F (32 °C), while a winter blackout during a cold spell leaves typical buildings at 32–43 °F (0–6 °C) — with high-performing buildings holding habitable temperatures for a full week (Urban Green Council, 2014).
Read together: the sealed modern envelope is an asset in cold and a liability in heat. The glass is what tips the balance — a high glazing ratio admits solar gain that the envelope then refuses to release.
For reference, the World Health Organization and the UK Health Security Agency (UKHSA) propose 18 °C as a safe minimum indoor temperature during cold seasons for general populations, and note that a higher minimum may be required for older people, children, and people with chronic illness, particularly cardiorespiratory disease (World Health Organization, 2018).
Water pressure failure: why high-rise booster pumps stop working
A prolonged grid failure directly impacts the water pressure booster pump high-rise systems depend on, cutting off upper floors. The second dependency fails faster than most residents expect, and it is pure hydrostatics.
Water loses pressure with elevation at 0.433 psi per foot, which is about 4.33 psi per ten-foot story (Mayer, n.d.). Most fixtures need roughly 20 psi residual to function; siphonic flushometer toilets need around 35 psi. Street pressure is therefore a budget, and each floor spends a fixed amount of it:
40 psi: 4.6 floors (hydrostatics alone); ~4 floors (realistic, with pipe friction).
50 psi: 6.9 floors (hydrostatics alone); ~6 floors (realistic, with pipe friction).
60 psi: 9.2 floors (hydrostatics alone); ~8 floors (realistic, with pipe friction).
70 psi: 11.5 floors (hydrostatics alone); ~10 floors (realistic, with pipe friction).
Above that line, water arrives only because an electric booster pump puts it there. When the pump stops, the taps on upper floors stop with it — not gradually, and not after the tanks drain, but as soon as whatever is already in the riser has been drawn off. Buildings with rooftop gravity tanks have a buffer measured in hours, and that buffer is shared with every other apartment above the pressure line.
The practical consequence is that water storage in a tower is not a supply problem but a vertical logistics problem. Water cannot be fetched upward at any useful rate — it weighs 8.345 lb per US gallon, and the lift is also out. Whatever a household will have is whatever is already above the pressure line when the power stops. This has structural implications of its own, which are worth working out before buying containers rather than after: the weight has to go somewhere.
Where the building has a gravity tank, filling available containers in the first minutes of an outage is the single highest-value action in the sequence, because it draws on a buffer that is about to be consumed by everyone else.
The window hazard: understanding stack effect and high-rise ventilation
Relying on open windows can backfire because the stack effect in high-rise buildings often pulls hot air upward. This is where general preparedness advice becomes actively counterproductive if applied without reference to conditions, because the correct answer inverts.
The stack effect, and why height changes the arithmetic
Warm indoor air is less dense than cold outdoor air, so in winter a tall building behaves as a chimney. Air infiltrates below the neutral pressure plane — the level at which indoor and outdoor pressures are equal, typically near mid-height — and exfiltrates above it. The pressure difference across the envelope grows with distance from that plane, peaking at the top of the building (Wilson & Tamura, 1968).
The magnitudes are not trivial. Wilson and Tamura give the example of a 50-story building at −25 °F developing a total stack effect of roughly 2 inches of water column, with differences across exterior walls in very tall buildings reaching about 1 inch of water.
One inch of water column is 249 Pa. Converted to a discharge velocity through an opening, that is an ideal 20 m/s, or around 12 m/s (27 mph) once a realistic discharge coefficient is applied. Opening a window on an upper floor in deep winter does not admit a gentle draught. It opens a pressurized outlet, and the building's accumulated warm air leaves through it at wind speed.
In storm conditions, wind pressure on the windward façade adds to this. The combination is why many towers have fixed or restricted-opening glazing above a certain height in the first place.
The resolution
The LBNL finding that natural ventilation is the most effective single heat measure and the stack-effect hazard are not in conflict. They apply to different conditions:
In heat, ventilate. Cross-ventilation is the highest-value action available, and withholding it to "keep the heat out" is the error that turns a sealed building into the thermos of the title. Ventilate hardest overnight, when outdoor air is cooler than indoor air — the LBNL work attributes the airtightness penalty specifically to trapped heat being unable to escape at night.
In cold, do not. Above the neutral plane, the exchange is strongly against you, and the building's thermal mass is the resource being spent.
In a storm, no openings on the windward face, regardless of temperature.
The test is not the season but the direction of advantage: open the envelope when outside air is cooler than inside air and the wind is not driving the façade, and keep it closed otherwise.
The passive cooling protocol: staying safe without power
Implementing a structured method for passive cooling without power is essential to naturally lower indoor temperatures. Everything below is deliberately non-combustion. No unvented heater, stove, grill, or generator belongs inside a sealed building under any circumstances — the envelope that makes these towers efficient is the same envelope that concentrates combustion products, and the early symptoms are indistinguishable from the stress of the outage itself.
Reduce the conditioned volume
The governing principle is that a household cannot condition an apartment, but it can condition a room — and in heat or cold, the best room is the same one: the smallest interior space with the fewest exterior surfaces. An internal bathroom, a windowless dressing room, or a hallway closed at both ends has minimal glazing, minimal exterior wall, and is buffered on most sides by other conditioned space.
In cold, a tented sleeping area inside that room further reduces the volume. The air a body has to warm is the air inside the tent, not the room, and a two-person tent pitched indoors reaches a workable temperature from body heat alone. Rigid insulation or stacked bedding beneath it matters more than the covering above, because conductive loss to the floor slab is the dominant path.
Thermal mass and water
Water's heat capacity works in both directions. Containers stored at room temperature moderate swings in the room they occupy; the same containers frozen and moved into the micro-climate room provide cooling later. This is one of the few genuinely dual-use items in a household's stock, establishing a solid baseline for your urban emergency preparedness strategy.
Ice, accurately costed
Ice is a real cooling medium and it is worth being precise about its capacity, because "phase-change cooling" tends to be oversold.
Melting ice absorbs 334 kJ/kg as latent heat of fusion, plus about 92 kJ/kg as the meltwater warms to room temperature — roughly 426 kJ per kilogram in total. In usable terms:
10 kg of ice delivers about 1.18 kWh of cooling: an average of 148 W over eight hours.
A resting adult emits roughly 100 W. So 10 kg of ice offsets the metabolic heat of about 1.5 people for one night, before counting solar gain through the glazing.
Matching a modest 1 kW cooling unit for eight hours would require about 68 kg (149 lb) of ice.
The conclusion is not that ice is useless but that its correct application is narrow: cooling a person, not a room. A shallow pan of ice with a battery fan drawing air across it, positioned at a seated or sleeping person, is an effective comfort measure. The same ice distributed around a room accomplishes almost nothing. Targeting the wrists, neck and ankles with cold packs is a better use of a finite amount of frozen mass than any attempt at ambient cooling.
Melting ice also adds moisture to a sealed room, which raises humidity and makes a given temperature feel warmer. Keep meltwater contained and drain it rather than letting it evaporate into the space.
Reflective barriers, and the one real caveat
Reflective material at the glazing reduces radiant gain in summer and radiant loss in winter, and this is where a genuine materials caution applies — though it is narrower than it is usually stated.
Thermal stress breakage occurs when one part of a pane is substantially hotter than another, and solar energy is the principal driver. Applied films "can significantly increase the risk" of breakage on float glass if incorrectly specified, and materials placed behind glazing — blinds and curtains among them — are recognized compatibility factors. Annealed and float glass are susceptible; heat-strengthened glass is highly unlikely to be affected, and tempered glass tolerates differentials of around 250 °C and is not at risk in normal architectural service (Vitro Architectural Glass, n.d.).
Three practical consequences follow:
The risk is solar-driven. A reflective layer on a window at night, with no sun on the glass, poses little thermal stress risk. The hazard occurs when reflective material is placed against sunlit glazing.
Leave an air gap and avoid partial coverage. An air space between the reflector and the pane lets accumulated heat dissipate, and covering a full pane uniformly avoids the sharp hot/cold boundaries within a single pane that generate stress. A half-covered sunlit window is worse than either a fully covered or an uncovered one.
Most tower glazing is safety glass, which is why this caution matters more in a converted building with original annealed glazing than in a recent curtain-wall tower. It is not possible to be certain from inside the apartment, which is why a convective air gap remains the non-negotiable default.
Ventilation discipline in a sealed room
A small interior room occupied by several people accumulates carbon dioxide and moisture. The aim is a reduced conditioned volume, not a sealed one: periodic door opening to the wider apartment is sufficient and necessary. Condensation on cold surfaces is a visible signal that the room needs to be exchanged with the rest of the dwelling.
When to relocate: managing extreme indoor heat
The LBNL authors state plainly that passive measures "will not work independently," and recommend backup power or relocation planning for vulnerable residents (Sheng et al., 2023). That conclusion should be read as written.
A household that includes an infant, an older adult, someone with cardiorespiratory illness, or anyone dependent on powered medical equipment is not the target for an endurance strategy. For that household, the protocol above buys the hours needed to arrange somewhere else to be—and the decision to move should be made early, while the lift situation, the stairs, and daylight are still manageable, rather than after temperatures have crossed a threshold.
The short version
The sealed, glazed tower fails fast in heat, not cold. Worst-case rooms crossed 30 °C (86 °F) in about 12 hours; cold took around 27 hours to reach the vulnerable-population threshold.
Airtightness is an asset in cold (safe hours ~9 → ~16) and a liability in heat (exposure +20%). An older leaky building is the reverse on both counts.
Natural ventilation is the single most effective heat measure — about 62% reduction. Ventilate hardest overnight.
Water pressure falls 4.33 psi per story. Above roughly four to eight floors, depending on street pressure, water arrives only by electric pump. Fill containers in the first minutes.
Opening a window on an upper floor in deep winter opens a pressurized outlet; stack pressures of 1 inch of water column imply draught velocities near 12 m/s (27 mph). No openings on a storm-facing façade.
Condition the smallest interior room, then a tent inside it. Insulate beneath, not just above.
Ice cools people, not rooms: 10 kg ≈ 148 W over eight hours, roughly 1.5 adults' body heat.
Reflective barriers at glazing: solar-driven risk only, air gap, full panes rather than partial coverage.
No combustion of any kind inside a sealed building.
A household with an infant, an older adult, or anyone medically dependent on power should plan to relocate, not endure.
The engineering conclusion is unsentimental. These buildings are better than their predecessors in almost every respect, including their resistance to cold without power. What they traded away was the ability to shed heat on their own, and that single dependency is one a household must cover deliberately, because the building will not do it unaided.
Continue reading
The full account of apartment-scale resource management during infrastructure failure — water, power, sanitation, food security, thermal regulation and building-specific hazards — is set out in The Grid-Down Apartment Survival Guide by Rowan Halsey.
This article is general information about building physics and passive thermal management. It is not an engineering assessment of any specific building, not medical advice, and not a substitute for the instructions of your building management or local emergency services. Never operate a generator, stove, grill, or any unvented combustion appliance inside a building. If anyone in the household depends on powered medical equipment, or shows signs of heat illness or hypothermia, contact your local emergency number and arrange relocation rather than relying on passive measures.
Disclosure: this article references a book written by the author of this site.
